Infrastructure Products
Matrox ConvertIP Series
ConvertIP DSS
Matrox ConvertIP DSS is a compact, standalone ST 2110 and IPMX transmitter/receiver device. Featuring 12G-SDI, genlock, one RJ45, and two SFP28 ports on a single device, ConvertIP DSS is designed for compressed or uncompressed workflows up to 25G and is optimal for an ultra-low latency experience. The device can receive power over Ethernet through its RJ45 connection, or it can be powered through an optional power supply unit. Both can be used simultaneously to deliver power redundancy.
Key Features
- 12G-SDI I/O
- Multi-network support
- 2x SFP28 (10G & 25G network support)
- 1x RJ45 (1G network support)
- Single device that transmits or receives IP signals
- Daisy Chain feature enables the reception and output of multiple streams from a single network port
- Standardized Discovery and Routing – based on AMWA NMOS IS-04 and IS-05 specifications
- Fanless design for quiet cooling
- PTP-derived genlock output support
- Genlock support for house sync input
- Power redundancy through PoE+ and locking AC power connector (optional power supply cable sold separately) Compact form factor mounts easily to the back of a monitor
- Web-based user interface for managing ConvertIP devices
- Complimentary ConvertIP Manager Windows application for simple commission and deployment
Transport formats
- IPMX
- ProAV Colibri codec for visually lossless transmission of compressed of media over 1G network
- Optional JPEG XS codec license for SMPTE ST 2110-22 support (up to 2 Gbps)
- Glass-to-glass latencies of 1ms achievable
Flexible ST 2110 and IPMX monitoring and multi-display with ConvertIP Daisy Chain
Boost your monitoring capacity and lower your total cost of ownership by driving multiple displays using a single network port on your switch with Daisy Chain.
-
Send multiple streams from a single network port to daisy-chained ConvertIP units. Ideal to minimize the number of SFP links to switch.
-
Create monitor walls with 2, 8, or even 16 displays, each outputting unique content using a single fiber cable.
-
Support multiple uncompressed or compressed streams on 10G or 25G links.
-
Reduce port usage, SFP, and fiber requirements driving down total cost of ownership.
-
Ensure uninterrupted operation in case of network problems and localize impact in case of a single device failure with support of ST 2022-7 redundancy.
*Feature available on ConvertIP DSH, SDM, and DSS models
Optional products
- ConductIP Media Routing Appliance to discover, route, and monitor ST 2110 or IPMX signals
- Bracket for VESA mounting behind monitors
- 1 RU rack shelf that holds three appliances
- Matrox NRG RPSU fault-tolerant, hot-swappable, and rack-mountable power supply
- Crestron Module to expand existing controlled environments
Technical specifications
|
Product |
|
|
Part number |
CIP-DSS |
|
Form factor |
|
ConvertIP product line
SDI to IP | Single media/control port | RJ45
SDI to IP | Dual media ports | RJ45 | Independent control port
SDI to IP | Dual media ports SFP | Independent control port RJ45 | Daisy Chain
HDMI to IP | Single media/control port | RJ45
HDMI to IP | Dual media ports SFP | Independent control port RJ45 | Daisy Chain | Pass through capabilities
HDMI to IP | Dual media ports | RJ45 | Independent control port | Pass through capabilities
HDBaseT to IP | Single media/control port | RJ45/SFP
IP SDM | Dual media ports | SFP/RJ45 | Independent control port | Daisy Chain
ConductIP
Your entire media installation at a glance
ConductIP is a standards-based signal routing platform that seamlessly discovers devices and routes signals to/from any NMOS-enabled end points—including ConvertIP—on SMPTE 2110 or IPMX-enabled networks. ConductIP gives you a comprehensive view of all device information on your IP network and where their signals are being routed, while allowing you to intuitively organize devices in your unique setup.
